SMPTE 2022-6 standard supports uncompressed video over IP sources. Video formats supported include MPEG-2 and serial digital interface. The fields below and some pre-defined configurations (for scanned sources) are available if you scan or manually add an RTMP uncompressed source.
There are three screens Common, Receivers, and Profiles, as shown below.
...
Fields | Description |
Label | A user-defined name for caption-display on the mosaic and system messages. |
Device | MCM9000 device the source is being monitored on. |
Access Type | Type of channel source (Uncompressed 2022-6). |
Service Type | Service type settings (SD/HD/Radio, etc.); used for system resource allocation. *Please note that altering this affects the resources used by the system and the quality of the monitoring. Service type refers to the number of hardware resources that should be allocated for monitoring the channel. Service type is usually measured by SD point (0.5,1,5,10,20...) depending upon the required hardware allocation which is usually detected during the scan. |
RecordingWhen | enabled, allows recording when there is an alarmNot relevant for uncompressed. |
Monitoring Level | Select the Monitoring level (Full, Light, Extra Light). Full Monitoring: One full license or and the full amount of SD points will be consumed by the system, and full monitoring will be done. Light Monitoring: A third of a license or One full license and a third of the SD points will be consumed, and the monitoring level will be for a third of the time. Extra Light Monitoring: A fifth of a license or One full license and a fifth of the SD points will be consumed, and the monitoring level will be for a fifth of the time. |
Tags | Specifying Tags enables filtering the sources based on tags. (E.g. Tag1) |
Note | General free text notes about the channel. |
Content | |
Audio Loudness Monitoring | Select the desired audio loudness measurement standard. EBU R 128 or ATSC A/85 (no gating). |
Hide Overscan | By default, overscan lines are hidden from the mosaic. Uncheck the checkbox for the full-frame display. |
Miscellaneous | |
Profile Automation Mode | Automatically chooses the profile from PMT Auto-Matching. If you want to choose Scheduler, enable the Scheduling Group |
Tally Mapping | Configure tally settings for the source. |
Snooze on Profile Change | Set time slot after profile change (in seconds), where errors related to the change are ignored. |
Unconfigured Component | Select the system response on detection of a PID which is not defined in the static channel configuration on the PMT:
|
Adhoc Activation Group | Enabling Adhoc activation groups allow automatic monitoring/unmonitoring of source. To configure, please refer to Adhoc Monitoring Workflow (Resource Grouping). |
Scheduling Group | Enabling scheduling groups, allows profile change in specific time zones. To configure, please refer to How to configure the scheduler on MCS. |
...
Recievers
...
Fields | Description |
Enabled | Enables the source and opens the connection. |
Networks | |
Network | The NIC used for this stream. (Primary) |
IP Address | The IP of the monitored stream. (Primary) |
Port | Source port number. (Primary) |
Source Specific Multicast | Set IGMPv3 for SSM. Leave empty for ASM. (Primary) |
Network | The NIC used for this stream. (Secondary) |
IP Address | The IP of the monitored stream. (Secondary) |
Port | Source port number. (Secondary) |
Source Specific Multicast | Set IGMPv3 for SSM. Leave empty for ASM. (Secondary) |
...
Fields | Description |
Type | Component type. Based on the selection, additional configurable fields will be displayed. |
Bit’s per Sample | Select 16, 20, or 24 bit. For a non-constant bit, select Don't care (aspect ratio related error notifications will be disabled). |
Type | Select the audio codec type from the dropdown. |
Dolby Channels Mapping | Select the Dolby channels mapping from the dropdown. |
Mapping
Mapping is available for Audio, Teletext, and Closed Captions.
...
Audio
...
Fields | Description |
Type | Audio mapping type. Based on the selection, additional configurable fields will be displayed. |
Receiver - Audio Layout | |
Template - Index |
|
Display Index |
|
Teletext
...
Fields | Description |
Type | Audio mapping type. Based on the selection, additional configurable fields will be displayed. |
Receiver - Page | Specify on which page to display. |
Template | Relevant for audio in uncompressed. |
Display Index | Position of the audio bars in the channel box. |
Closed Captions
...
Fields | Description |
Type | PID payload type. Based on the selection, additional configurable fields will be displayed. |
Receiver | |
Template | Relevant only for audio in uncompressed. |
Display Index | Position of the audio bars in the channel box. |
Closed Caption | Select the closed caption type from the dropdown. Choose Hide if you don't want to show the CC. |
Click on the save icon to save the changes.